The post Stainless Ball Valve for FermZilla – PCO 1881 x 3/4 in. Female BSP appeared first on Quirky Homebrew Supply.

The post 100mm Metal Lid for Wide Mouth Jars (Each) 100-2055 Lug Finish – With Stopper Hole appeared first on Quirky Homebrew Supply.

The post Basic Food Fermentation Kit – Flip Top Jar with Airlock – 1L / 33.8 oz appeared first on Quirky Homebrew Supply.

This particular lid was designed in order to suit a growing number of customers desire to dry hop without exposing the batch to oxygen from opening the lid. By using this lid in conjunction with the FermZilla 2" Butterfly Valve and Hop Bong Kit, you will be able to purge CO2 into the tube and expel all the oxygen inside it and dump freely into the vessel.

Features:

(2) PCO1881 Male Ports
Recommended for use with Red (Gas In) & Yellow (Bev Out) Ball Lock Caps
PRV Port with Red 35 psi (2.5 BAR) PRV
2" T.C. Ferrule
Undrilled Ports (for optional accessories):

Thermowell Port (see below for FermZilla Thermowell kit)
(2) Temp Twister Ports
Please Note: Temp Twister will need to be bent on a 20° Angle in order to fit on the curved lid and align vertically in the tank.

Also includes:

2" Tri-Clamp
2" T.C. Gasket
2" T.C. x PCO1881 Male Thread Cap
If you ever need to replace the O-ring attached to the bottom of the Pressure Lid, a Corny Keg Lid O-ring fits perfectly.

KegLand Part Number: KL28219

Warning: Always depressurize your system COMPLETELY before removing fittings from your fermenter.

Warning: Only use Red 35 psi PRV with this lid. Ensure the PRV is cleaned and dried of sticky residue before each fermentation. Failure to do so could cause injury and void warranty.

The post Tri-Clamp Pressure Lid for FermZilla – 2 in. appeared first on Quirky Homebrew Supply.

If you are experiencing leaking from the top lid section, this slightly thicker O-Ring will aid in resolving said leaking. To perform a leak test, please remember to have the unit free of any liquid as that will absorb CO2.

It is also important to remember not to overtighten the stainless steel handles that may have come with your FermZilla. Over-tightening will cause the opening to warp and not seal. The handles should be able to freely rotate around the neck with little resistance.

KegLand Part Number: KL22262

The post Replacement Lid O-Ring for FermZilla appeared first on Quirky Homebrew Supply.

These are ideal for the BrewZilla & DigiBoil ball valves, 25-Watt MKII Magnetic Drive Pump, or any 1/2" NPT or BSP connection.

Features:

Stainless steel and silicone construction
High temp silicone grip provides a cool touch even with hot liquids!
Ribbed grips allow quick comfortable tool-free operation
Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced
Fits all male 1/2" NPT and BSP fittings
1/2" (13mm) stainless steel barb tail with 3/8" (10mm) ID bore
KegLand Part Number: KL31639

The post KegLand Quick Swivel Connector | 1/2″ x 1/2″ Straight Barb appeared first on Quirky Homebrew Supply.

The post Stainless Steel Pressure Kit for 27L FermZilla appeared first on Quirky Homebrew Supply.

The post Wide Mouth 1 Gallon Fermentation Setup – Glass Carboy with Stopper and Airlock – 128oz appeared first on Quirky Homebrew Supply.

Lids are not included, see our 100 mm lug finish metal lids

The post Glass Fermentation Jar | 1 Gallon | No Lid | 100mm Lug Finish appeared first on Quirky Homebrew Supply.

The post 100mm Metal Lid for 1 Gallon Wide Mouth Jars (Each) 100-2055 Lug Finish appeared first on Quirky Homebrew Supply.