BrewZilla All Grain Brewing System With Pump – 35L/9.25G (220V)
The BrewZilla is an all-in-one electric brewing system that has built in elements for heating and boiling, programmable mash schedule and delayed start, a built in pump for recirculation, an onboard water resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built in spigot for transferring. It is extremely portable and uses 110V power so it can be used nearly anywhere.
The V3.1.1 unit features an upgraded main circuit board that changes how the automatic step mashing functions. Now when moving from step to step, the timer for each step will not begin counting down until the programmed temperature is reached. This means more accurate mash schedules than ever before! The new board also introduces boil addition timers so you’ll never miss the mark for hop additions.
New accessory! Check out the BrewZilla Whirlpool Arm, which uses the unit’s internal pump to recirculate and spin the wort, improving hop extraction and chill times. No more stirring!
Automatic Step Mashing!
One of the coolest features of the BrewZilla is the ability to program the unit with up to 6 individual temperatures and durations so you can step mash precisely how you desire. Simply press the “S1-S6″ button to select the stage you want to adjust, and use the temp, time and +/- buttons to program the stage. If you have less than 6 stages in your mash schedule, program the stages you want to skip with 00:00 as the time and the controller will automatically move on to the next step. When all the stages are complete, the BrewZilla will sound an alarm and hold the last set temperature.
The programmable stages can also be used to set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or wake up in the morning. In order to do this, fill the unit with strike water and program the controller with two steps. Step 1 should be programmed at a temperature lower than the unheated strike water (so the elements will remain off), and the duration should be programmed for however long you want the delay. Then program Step 2 with your desired strike water temperature and a duration of 1-2 hours, giving the BrewZilla ample time to heat up and giving you a margin of error in case you hit the snooze button the morning of brew day.
Built in magnetic drive pump to easily recirculate the wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter.
Dual heating elements run off of a single 110 volt plug and have individual switches allowing for more control over the heating process. One element is 1000 watts and the other is 500 for a combined 1500 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature.
The digital control panel makes it easy to see the current temperature and set the temperature you want. The digital controller is also water resistant so don’t worry about spills or some water dripping down the side. This controller is built for brewing!
The brewery also includes a stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it from the BrewZilla and tabs at the base so you can set the malt pipe over the BrewZilla to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging.
The included stainless wort chillers is shipped with bare ends so you can set it up for your situation. We list below the most common tubing and fittings sold to help connect to a hose, hose bib, or faucet.
Note: The manual references an element for a different market. This unit comes with two heating elements for a total of 1,500 watts.
Stainless steel construction
9 gallon total capacity with a finished beer output of 5-6 gallons
Digital temperature controller
Automatic step mashing with 6 programmable stages
110V power and plug
Dual heating elements for total control (1000 watts and 500 watts)
Stainless steel 1/2 in ball valve for draining (don’t have to use the pump)
Immersion wort chiller included
Stainless steel malt pipe/basket
Stamped volume markers
Magnetic drive pump for recirculation
Temperature reads in °F or °C (press and hold temp button for several seconds to adjust)
32.75 in H (with recirculation arm) x 12.5 in D
Recommended max. grain bill – 18 lbs
Recommended min. grain bill – 8 lbs
You might also want:
2′ of 1/2″ ID Silicone tubing for sparging and draining.
To connect included chiller: 20′ of 1/2″ ID tubing, 3 small hose clamps and 1 brass Garden Hose Thread by 1/2” barb adaptor.